絶対位置決め精度とは何ですか?
絶対位置決め精度 座標値で指定された任意の位置決めポイントに、位置決めを行った場合の、座標値と実測値の差。
寸法精度とは何ですか?
寸法精度とは工作物の長さ、直径、厚み、キー溝幅など指定部分の寸法の正確さを言います。 部品が機械に組み込まれ、適切に動作するにはこの寸法精度が重要です。 もし寸法が正しくないと機械が故障を起こす原因にもなります。 これを防ぐには、部品設計時に肝となる部分の寸法精度が出るように図面で公差を指示する必要があります。
寸法精度と形状精度の違いは何ですか?
2.加工精度に関する内容(1)寸法精度加工部品の実際のサイズと部品サイズの公差域の中心との間の適合度を指します。 (2)形状精度機械加工部品の表面の実際の形状と理想的な形状との間の適合度を指します。
機械の位置決め精度とは?
位置決め精度とは、工作機械の試験・検査などにおける基本事項関連の用語の一つで、直線運動における位置決めや回転運動における位置決めなどの、設定した目標位置に対して実際に停止した位置の正確さの意味です。
繰り返し位置決め精度とは?
同じ位置に同じ方向から繰り返し位置決めをおこなったときに、どれだけの誤差が生じるかを表した値です。 精度は一定温度、一定負荷での値です。
JISの繰り返し位置決め精度とは?
繰り返し精度[JIS B 6191-1993準拠]
任意の1点に同じ方向から位置決めを7回繰り返して停止位置を測定し、測定値の最大差を測定します。 測定は移動距離の中央、両端の位置で行い、求めた差の最大値の1/2に±を付けて「繰り返し精度」とします。
精度の求め方は?
一般的に精度と呼ばれるもので、「正解数/データ数」で計算できます。
フルスケールとはどういう意味ですか?
フルスケールとは、対象の測定装置の全測定範囲の幅ことを示します。
繰り返し精度とは何ですか?
同一の条件,同一の方法で比較的短時間内で測定対象を繰返し測定したときの測定値のばらつきをいう. 通常最大値と最小値の差で表す.
形状精度とは何ですか?
形状精度とは、工作機械の機械精度及び工作精度にかかわる用語において、各種工作機械での構成要素や工作物の形状に関する幾何学的な正確さのことです。
機械精度とは何ですか?
機械精度とは、工作機械の試験・検査などにおける基本事項関連の用語の一つで、静的精度(無負荷状態での構成要素の形状、位置、運動及び相対的な姿勢の幾何学的な正確さ)と位置決め精度(各運動軸による位置決めにおいて、設定した目標位置に対する実際に停止した位置の正確さ)の総称のことです。
位置決め精度の測定方法は?
位置決め精度検査には、レーザ干渉位置計測システム(レーザ測長器)を使用しています。 これは、レーザの波長を目盛りとして利用し長さを測る測定器です。 位置決め精度検査ではこの測 定器を使用して、直線移動軸の基準位置からの移動量を測定します。
割り出し精度とは何ですか?
割出精度 割出精度は、測定した角度のずれの最大値と最小値との差を累積として表現しています。 累積値の半分に±を付けて表現する場合もあります。
位置決め精度の求め方は?
位置決め精度とは位置決め動作(アクチュエータを目標の点で止める動作)を行ない、目標点と実際の停止位置との差の絶対値を求めます。任意の一点へ同じ動作方向からの位置決め(アクチュエータを目標の点で止める動作)を7回繰り返して停止位置を測定し、停止位置の最大値と最小値の差を求めます。
繰返し精度とは何ですか?
繰り返し精度とは、同一の条件下、同一の対象物に1台の測定器で、定点を繰り返し測定したときの値のバラつきを表します。 この値が小さいほど繰り返し精度が高く、安定して高い精度での測定ができることを示します。
4桁の精度は?
精度 | 有効桁数での丸め | 小数点以下での丸め |
---|---|---|
4桁 | 12.35 | 12.3450 |
3桁 | 12.4 | 12.345 |
2桁 | 12 | 12.35 |
1桁 | 1E+1 | 12.4 |
絶対精度と相対精度の違いは何ですか?
絶対精度とは、「モデルサイズに関係なく最小距離が決まっている」もの。 一方相対精度とは、「モデルサイズに応じて最小距離が変化する」ものです。
リードスケール精度とは何ですか?
RS(リードスケール精度)とは、どの流量域でも、指示(表示)値に対して何%という考え方です。 「%RD」「%RS」「リーディングスケール」などと表記します。 FS(フルスケール精度)とは、測定最大値(フルスケール)を決め、その最大値に対して何%という考え方です。
RDGとFSの違いは何ですか?
流量計・流量センサの精度は、フルスケールに対して何%の誤差があるのかを示す「フルスケール(F.S. ) 精度」と、指示(表示)値に対して何%の誤差があるのかを示す「リードスケール(RDまたはRdg)精度」の2つがあります。
繰り返し位置決め精度の測定方法は?
1. 繰り返し位置決め精度
任意の一点に同じ方向からの位置決めを7回繰り返して停止位置を測定し、読みの最大差の1/2を求めます。 この測定を移動距離の中央および、ほぼ両端のそれぞれの位置で行い、求めた値のうちの最大のものを測定値とし、その値に±の符号を付けて表したものです。